节点文献

氢化钛粉末及压坯的脱氢规律

Research on dehydrogenation of TiH2 powder and TiH2 green compact

  • 推荐 CAJ下载
  • PDF下载
  • 不支持迅雷等下载工具,请取消加速工具后下载。

【作者】 李红梅雷霆张家敏方树铭尚青亮刘捷

【Author】 LI Hong-mei1,LEI Ting2,ZHANG Jia-min1,FANG Shu-ming2,SHANG Qin-liang3,LIU Jie3 (1.Faculty of Metallurgical and Energy Engineering,Kunming University of Science and Technology, Kunming 650093,China; 2.Kunming Metallurgy College,Yunnan 650033,China; 3.Technical Center of Yunnan Metallurgical Group Co.,Ltd.,Kunming 650031,China)

【机构】 昆明理工大学冶金与能源工程学院昆明冶金高等专科学校云南冶金集团股份有限公司技术中心

【摘要】 通过热重分析(TGA)研究TiH2粉末粒度对其脱氢温度及脱氢量的影响,采用热膨胀仪研究粉末粒度对TiH2压坯收缩率的影响,同时利用真空烧结炉研究成形压力和温度对TiH2压坯烧结脱氢的影响。结果表明:TiH2粉末粒度越细,起始脱氢的温度越低;与粒度约为45μm的原料TiH2粉相比,经过球磨的粉末脱氢量减小;球磨30 min后的TiH2粉末压坯,烧结线收缩率和收缩速率都显著增大;原始TiH2粉末压坯和球磨30 min后粉末压坯的最大收缩率分别为5%和9.5%,最大收缩速率分别为2.4×10-4和7.30×10-4μm/℃;成形压力越大,TiH2压坯脱氢峰值温度越高,650℃保温1 h,TiH2压坯失重率达到3.572%(理论含氢量为4.01%)。

【Abstract】 The effects of TiH2 powder size on dehydrogenation temperature and the amount of dehydrogenation were investigated by TGA.The shrinkage behaviors of compacts with different powder size were analyzed by a Dilatometer.The influences of compacting pressure and temperature on dehydrogenation behavior of TiH2 green compact were conducted in a vacuum furnace.The results show that,the finer the powder size,the lower initial dehydrogenation temperature.The weight loss reduced for ball milling powder and the linear shrinkage and linear shrinkage rate of fine TiH2 powder milled for 30 min were significantly increased,compared with raw TiH2 powder(~ 45 μm).The highest linear shrinkage is 5% for raw TiH2 powder and 9.5% for ball milling 30min and the highest linear shrinkage rate is 2.4×10-4 and 7.30×10-4 μm/℃,respectively.The peak temperature of dehydrogenation of TiH2 green compact with high compacting pressure is relatively higher than that of low compacting pressure green compact.Being dehydrogenated at 650 ℃ for 1 h under high vacuum,the quantum of dehydrogenation reached 3.572%(theoretical hydrogen content 4.01%).

【关键词】 氢化钛脱氢粉末冶金
【Key words】 titanium hydridedehydrogenationpowder metallurgy
【基金】 国家科技部国际科技合作资助项目(2009DFB50410);云南省科技厅国际科技合作重点资助项目(2009AC012)
  • 【文献出处】 粉末冶金材料科学与工程 ,Materials Science and Engineering of Powder Metallurgy , 编辑部邮箱 ,2012年02期
  • 【分类号】TF123.111
  • 【被引频次】7
  • 【下载频次】438
节点文献中: 

本文链接的文献网络图示:

本文的引文网络